How it works
Four main pieces, connected in a line.
Outside
Only the solar panel. A single MC4 cable runs from it, through a wall or door gap, to the cupboard.
Inside (a cupboard or box)
Battery, charge controller and fuse. The warmer's USB lead runs from the controller to the cage.
The one thing to remember about order: battery connects to the controller first, solar panel last. When taking it apart, do the reverse: panel off first, battery last.
Shopping list
Amazon US links. Prices are estimates and change often. Tick things off as you order them โ the ticks are saved on this device.
Pick one bird warmer
-
Fenocran 5V USB Bird Warmer PadOption A~$35โ45Plugs directly into the controller's USB port; chew-resistant cord.
-
K&H Snuggle-Up Bird Warmer (orange, USB-A)Option B~$49MET-certified alternative; also plugs directly into the controller's USB port. Make sure it's the USB-A version.
Power system
-
ECO-WORTHY 100W Rigid Solar Panel~$62Captures daytime sun to recharge the battery.
-
ECO-WORTHY 12V 20Ah LiFePO4 Battery~$63โ74Stores 256 Wh (1โ2 nights of heat). Uses M5 terminal screws.
-
Renogy Wanderer 10A PWM Charge Controller~$24Regulates charging; has a 5V/2A USB port for the warmer.
-
WindyNation MC4 Solar Cable~$15โ25Runs from the panel outside to the controller inside. Choose a length that covers the whole route.
-
12 AWG Inline Blade Fuse Holder Kit~$8โ10Holds a 15A safety fuse on the battery's positive (red) wire.
Optional
-
12 AWG Red & Black Copper WireOptional~$15โ20Battery-to-controller wires. Skip it if you'll cut a short piece off spare solar cable instead.
-
Renogy Adjustable Tilt BracketsOptionalvariesAngles the panel towards the winter sun for more charge on short days.
Tools & bits you'll probably need
- Small flat & Phillips screwdrivers
- Wire stripper / cutter
- Crimp tool for the fuse holder connectors
- 2ร M5 ring terminals for 12 AWG wire (often in the battery or fuse kit)
- Spare 15A blade fuse
- Cable ties or clips
- Thin foam board (if winters freeze)
- Multimeter (nice to have)
Wiring diagram
Every connection in the whole system. Red is positive (+), black is negative (โ).
The controller's terminals are marked with small icons (panel, battery, light bulb). Go by the icons, not the position in this drawing. The LOAD terminals stay empty.
Step by step
Tick each step as you finish it. Your progress is saved on this device.
-
Unbox and check everything
Lay out all the parts. Check the battery and panel for damage. Leave the solar panel face down or covered with cardboard โ it makes voltage as soon as light hits it.
-
Choose where everything goes
- Panel: outside, facing the sun for as much of the day as possible (south in the northern hemisphere, north in the southern), clear of shade.
- Battery + controller: in a dry cupboard or box, close to the cage, where the controller's screen can be seen.
- Plan the route for the MC4 cable from panel to cupboard, and the USB lead from controller to cage.
-
Mount the controller
Screw the controller to the inside of the cupboard, upright, with a little air space around it. Put the battery next to it on a flat, stable surface.
-
Make the battery wires
Cut a short red and a short black 12 AWG wire long enough to reach from the battery to the controller. Strip about 8 mm (โ in) off each end. Crimp an M5 ring terminal onto the battery end of each wire.
No spare red/black wire? A short piece cut off the solar cable works too.
-
Add the fuse holder to the red wire
Splice the inline fuse holder into the red (+) wire, within 6 inches (15 cm) of the battery end. Leave the fuse out for now.
The fuse protects the wire from a short circuit. Keeping it out until the end means nothing is live while you work.
-
Screw the battery wires into the controller
At the controller's battery ๐ terminals: red wire into +, black wire into โ. Tighten firmly and tug each wire to check.
-
Connect the battery and insert the fuse
Bolt the ring terminals onto the battery with the M5 screws: black to โ first, then red to +. Then push the 15A fuse into the holder.
The controller's screen should switch on. It reads the battery and sets itself to 12 V automatically.
Never let the red and black ends, or a tool, touch both battery terminals at once.
-
Set the battery type to Lithium (LiFePO4)
The Wanderer ships set for lead-acid batteries. Use the front buttons to change the battery type to Lithium / LI.
Usually: hold the SELECT (or MODE) button until the battery type flashes, press to step through the types until Lithium/LI shows, then hold again to save. The exact buttons are in the little manual that comes with it.
-
Run the MC4 cable
Mount the panel outside (on tilt brackets if you bought them) and keep it covered. Run the MC4 cable from the panel to the cupboard. Use a drip loop (a small dip in the cable) where it enters the building so rain runs off rather than in.
-
Screw the cable into the controller's solar terminals
Strip the bare ends of the MC4 cable inside the cupboard and screw them into the controller's solar โ terminals: red/positive into +, black/negative into โ.
-
Plug the cable into the panel, then uncover it
Click the MC4 connectors onto the panel's leads (they only fit one way round). Then remove the cover. The controller should show that it's charging (a sun or charging icon).
-
Plug in the bird warmer
Plug the warmer's USB lead into the controller's 5V USB port. Fit the warmer to the cage as its instructions show, and keep the cord where the bird can't reach it.
Give the pad about 15 minutes, then feel it: it should be gently warm, not hot. Leave space in the cage for the bird to move away from it.
-
Protect the battery from frost
LiFePO4 batteries must not be charged below 0 ยฐC (32 ยฐF). If the cupboard can freeze, line it with light foam board around the battery (leave the controller some air).
Checks & care
What to keep an eye on once it's running.
| When | Check |
|---|---|
| First evening | Warmer is on and gently warm; controller shows the battery level. |
| Next morning | Battery still has charge left after the night. |
| After a sunny day | Battery is back to full (or close to it). |
| Cold snaps | The cupboard isn't freezing; a few cloudy days in a row will run the battery down. |
| Monthly | Wipe the panel, check wires are tight and the cord isn't chewed. |
If something's not right
Controller screen is blank
Check the fuse is in and not blown, the battery terminals are tight, and red goes to + on both ends.
Warmer isn't warm
Battery may be empty (the controller cuts power to protect it). Check the battery level on the screen, and try the warmer in a phone charger to rule out the pad itself.
Battery never gets full
The panel is shaded for part of the day or angled badly. Winter sun is low, so tilt the panel steeper. Also check the battery type is still set to Lithium.
Need to disconnect everything
Reverse order: unplug the warmer, cover the panel and unplug the MC4 connectors, pull the fuse, then unbolt the battery (red first, then black).